This is how to make a fabric headboard

how to make a fabric headboard,how to make a fabric headboard,how to make a fabric headboard

This is how to make a fabric headboard

Upcycling: How to make a texture secured headboard

Originator Cassandra Ellis makes a lovely texture secured cushioned headboard.

YOU WILL Require

9mm plywood sliced to measure. DIY stores with wood-cutting machines can do this for you. You can pick any stature for the headboard however you’ll need it sliced to a particular width to coordinate the bed. These cutting aides depend on UK bed sizes, so on the off chance that you have an European or US bed, check the bed size and include 2-3cm for the right cutting size:

Single 92cm

Twofold 137cm

Lord 152cm

Super Lord 183cm

Ruler 203cm

4cm thick upholstery froth to cover one side of the plywood

Upholstery wadding/batting, 10-15cm bigger than your plywood all round (upholstery froth and wadding are effortlessly accessible from eBay)

Enough texture to wrap around your headboard, in addition to an additional 20cm in width and tallness

Indelible marker

Utility blade

Staple weapon

Texture scissors

Shower glue

D-rings, to mount your headboard to the divider


1. Lay the upholstery froth on a table or clean floor, and afterward put the plywood on top. Follow the diagram of the board onto the froth, then cut the froth with an utility blade.

2. Rehash this procedure with the wadding however include 10-15cm each of the four sides so you can wrap it over the edge of the plywood when you secure it.

3. Stick the froth to the plywood utilizing splash glue (make sure to open windows and ideally wear a cover) and let this dry.

4. Spread the wadding out on the table or floor and focus the headboard on top, froth side down. Staple the wadding to the back of the plywood, pulling it tight as you go – this is vital.

5. Press your texture and afterward put it on the table or floor, right side down. Ensure that it is level and without wrinkle. Put the headboard on top with the plywood back confronting you. On the off chance that your texture has an example or clear stripe, take mind where you position the headboard, as a somewhat off-piste stripe can be awkward to take a gander at.

6. Beginning at the top focus, working outwards and pulling firmly as you go, staple the texture to the back of the wood. At that point do the base edge similarly, trailed by the two sides. When you achieve the corners, crease the texture flawlessly, as though you were wrapping a present. Once the whole headboard is secured, trim any abundance texture.

7. Join your headboard to the divider by screwing two D-rings to the back of the plywood and hanging them from tightens or snares your divider.

Taken from Home Sewn by Cassandra Ellis (£19.99, Kyle Books). Photography by Catherine Gratwicke.

how to make a fabric headboard


My most loved activities appear to be the ones that take motivation from top of the line stores or magazines. It is such a fun test to check whether I’m ready to reproduce the search for significantly less, so when my mother had her eye on a tufted headboard at one of our most loved stores we knew we had our next venture staring us in the face.

Try not to give the completed look a chance to trick you. This venture is substantially less demanding than it might appear, and at last you will have a delightful upholstered headboard!

DIY Upholstered Headboard

This is the third room that I’ve helped my mother with! She initially requesting that I help her with the grandkid’s room and after that got back to me into help with her brilliant and striking lounge room! Since we’ve advanced into the main room, I’m supposing I’m formally procured! What’s more, it works out splendidly since I take her minding appropriate installment!

I initially shared this venture over at Remodelaholic and can hardly wait to demonstrate to all of you how simple it was. We utilized pegboard as the casing sponsorship to make this venture truly straightforward. It makes it so natural to include catches since the openings are now there! How about we begin.




2 x 4 wood

a sheet of peg board

1 inch froth

light weight batting

splash glue

upholstery weight texture


trellis wire

substantial mirror/picture holders

The most effective method to Assemble THE HEADBOARD Outline

Building the casing might be the most threatening some portion of this venture particularly on the off chance that you don’t have or know how to utilize control devices. Try not to stress. Most handyman shops will make the cuts for you ideal in the store, so you leave with everything slice and prepared to collect.

The span of your headboard edge will rely on upon the measure of your bed. We made this headboard outline an indistinguishable width from the bed outline. The tallness is dependent upon you. A smart thought is tape it off utilizing painters tape to discover how tall you need it to be. When you know how high you need it, measure from the highest point of your bed edge to the tallest point on the divider. Whatever estimations you thought of will be the size that you have the peg board cut. At that point you will outline it on the posterior with 2 x 4’s as demonstrated as follows.

the most effective method to manufacture a headboard outline with peg board

When you have your casing gathered, you will need to arrange out the situation of your catches. We had 5 catches crosswise over and 3 catches down.

Catches going over: We separated the width of the pegboard by 6 (however many catches you have going crosswise over + 1) and utilizing a measuring tape we denoted the width of each segment on the back along the top.

Vertical catches: First we subtracted the space that the sleeping cushion would cover before starting. In this way, take the stature of your pegboard – the thickness of your bedding. Presently take that number and partition by the quantity of vertical catches + 1. (We have 3 vertical catches, so we separated by 4 to get 4 square with segments as demonstrated as follows.) Then measure down from the top (where you made your first stamp for the catches going over) and locate the nearest opening. Rehash moving down and stamp each opening, then move crosswise over until you have the greater part of your catches checked.

vertical catch estimations

We denoted our own on the posterior with a hover around each opening. You might need to check the front as well, to make sure you have a visual of where your catches will be on your completed venture. Better to discover any oversights now, versus later!

how to make a fabric headboard

denoting the gaps


We had a 1 inch bit of froth cut at our nearby upholstery texture store. Along these lines it was one major piece without any creases.

Line up the froth with the edges of the edge, lay the casing level (front side up), and apply the froth to the front of the edge with shower adhesive.attaching the froth to the headboard outline

Once the froth is joined, lay out your lightweight batting and lay the edge on top with the froth confronting down. Trim your batting so that when you wrap it up and around the sides of the casing you can connect it on the posterior of the edge. Staple it set up utilizing a staple firearm, ensuring that the corners lay level (like you are wrapping a present.)attaching the batting to the headboard outline

Including THE Texture:

Lay your bit of texture out level with the great side confronting down. Once more, lay the casing face down on the texture. At that point, crease the edges of the texture up and over the edge and connect with a staple weapon.

My best guidance is to begin with the sides, ensuring that you pull the texture tight, and afterward do the top and base of the casing. The corners will take a tad bit of practice to motivate them to lay pleasantly, yet simply play around with them until you like what you have, and staple them set up. Keeping the crease along the edge of the edge will give it a truly decent completed edge.

upholstered headboard

Including the catches:

On our first endeavor we had upholstery string and a gigantic needle. It didn’t work. What worked was trellis wire! (Who knew?) Any wire that is effortlessly twisted, yet not very delicate with the goal that you can jab through the froth and texture will work. You will likewise need to make certain that your wire is not very thick. You should have the capacity to go it through your catch openings.

Once the texture was on we set the casing on its base edge and began including our catches. This is a 2 man work. I cut a bit of wire, then jabbed it through the headboard where we denoted our openings. At the point when the wire got through the front, my mother included the catch, and after that twisted it and drove it back through the texture near where it initially came through. You may need to jab around a tiny bit to discover the gap once more.

upholstered headboard with catches

When it returned through to me, I pulled the catch tight by spreading the 2 pieces separated in inverse bearings. My mother was eyeballing the tufting as I pulled to ensure that the wrinkles that were made were the look she needed, and even starting with one catch then onto the next.

I stapled each side of the wire set up and after that pulled them back together and bent them to keep them set up. At that point we rehashed this procedure until every one of the catches were on!

appending the catches

What’s more, this is the consequence of our DIY endeavors!

DIY Upholstered Headboard


We hung the edge on the divider so that the base was recently over the bed outline utilizing these extensive picture/reflect holders. The simple directions were on the bundle and it made the headboard strong against the divider.

hanging the headboard

Not very shabby for an evening’s work huh?

DIY no sew upholstered headboard instructional exercise

Between the example on the divider and the new headboard this room is set for an extraordinary begin! The principle point of convergence is set up and she says she grins each time she strolls into the room. I’d say that is an occupation well done!

blog entry signature